CNC Hydraulic Bending
LPDY100T/3200
Angle bender
Control system
Adopts Cybelec of Switzerland that the world famous professional operating system of bending machine, excellent intelligent control system combined with excellent hardware configuration, makes the performance of the machine play perfectly. Sequence programming function, angle programming function, back gauger avoidance function, manual axis shifting function, queue jumping function during operation, the friendly system design makes it easy for users to obtain a simple and professional use experience.
Down moud selection
When bending different thicknesses of metal sheet, only need to select fifferent size of "V" groove of bottom molds, the size of V groove should be 8-10 times than the thickness of metal sheet. For example, when bending 6mm sheet the 48-60mm V groove is required. This machine adopts hydraulic transmission, which is stable and easy to operation, the table is equiped with a mechanical deflection compensation mechanism it ensure a high accuracy over the entire bending length.
Machine structure
1. The machine adopts a steel plate welding structure with sufficient strength and rigidity. The hydraulic transmission ensures avoid serious overload accidents are caused due to changes sheet thickness or in-suitable of the V-groove of the down-moud. 2. Special designed mechanical stop inside the oil cylinder it ensure the repeated positioning accuracy of the slider to the bottom dead center, so as to ensure the consistency of the bending angle during mass production. 3.Complet annealing processing after machine frame welded to ensure that the machine does not deformation for a long time working. 4. The whole frame adopts sanding method to remove rust, and is coating with anti-rust paint.
Hydraulic system
1、The excellent hydraulic system can realize the rapid upward and slow descending of machine slider, it increased working efficiency and security of machine.
2、The type of oil pump adopts gear pump, it withstand high pressure and low noise.
3、Adopts top brand of oil seals, good sealing performance and long service life.
4、The machine tool can work continuously under the rated load, the hydraulic system is leak-free and continuously stable with high accuracy.
Electrical parts
1、Electrical components adopts international famous brand, it can be almost runing without maintenance for long-term.
2、Equiped with removable foot switch, easy operation.
3、The main circuit of the motor with protected function against short circuit / overload and phase loss.
Compensation mechanism
The user only needs to input the compensation value according to the actual measured value of bended working piece, the compensation device will adjusting the compensation angel automaticly by the operating system, the digital operation greatly improves the bending accuracy.
Back gauge
The back gauge is driven by a servo motor through a synchronous belt and a synchronous wheel to drive the ball screw. The back gauge is supported by four linear guides. It has high repeated positioning accuracy, reliable structure, fast positioning speed, low noise and vibration, and high bearing capacity. The standard R-axis ascends and descends as a whole, which has a great advantage when bending complex workpieces, and it covers the transmission part with a safety cover, which is multi-effect.
Mould fixture
The mould fixture adopts new type of two-stages fast mould clamper, this mould clamper designed with two-stage structure it can be proper fit with the shape of up-mould, it make clamping the up-mould automaticly become to a straight line. The mould clamper with handle open/close design, It make changing mould does’t require any tools, realized easy and fast to changing mould without turning any srews. The design of two-stages structure of the clamper except proper fitting with mould meanwhile have cared about safty when change the mould, its hook shape structure can hold the mould while the handle in open position, user can change the mould freely without worry it fall down from clamper.
Conditions of Use
1、 Power: 380V ± 10%, 50Hz 12kw.
2、 Ambient temperature: 5-38 ° C (temperature during operation).
3. Ambient humidity: relative humidity 20-80% RH.
4. Keep away from strong vibration sources and electromagnetic interference sources.
5. No harmful and corrosive gas.
6. The bending machine’s self-weight is un-even at front and back, to aviod machine tip forward, the thickness of solid cement floor should not less than 15cm.
1.Quality Control
Skilled and strict Quality Inspection Team is available during the material purchasingand production procedure. All finished machine we delivered are 100% strictly tested by our QC departmentand engineering department. We will provide detailed Machine pictures and Test videos to customers before delivery.
2.OEM Service
Customized and OEM orders are welcome due to our aboundant experiences.All the OEM services are free, customer only need to provide us with your logodrawing. function requirements, colors etc. No MOQ required.